Kiilto Pro Grip
Tackifier adhesive
Rollable tackifier adhesive for a wide range of removable textile and vinyl floorings. Allows easy change of floor coverings whenever required.
Special features
- Ready-to-use
- Rollable
- Good adhesion
- Long assembly time
- Permanent tack
- 2-Ethylhexanol-free
- Does not contain phthalates
Links
Materials
For both absorbent and non-absorbent substrates indoors, suitable for dry and wet areas. Compatibility for bonding most coverings:
- Textile coverings with structured or integrated backing
- Vinyl floors and tile
- LVT approved for tacky gluing, e.g. Forbo Allura Flex
Suitable with underfloor heating and castor wheels traffic.
| Package Size | Product Code | EAN Code |
|---|---|---|
| 5 l | T3793.005 | 6411513793053 |
| 10 l | T3793.010 | 6411513793107 |
+18-25 °C
Short hair roller: 6 – 10 m²/l
Plain steel trowel: 8–12 m²/l
1.0 kg/l
5 l, 10 l
In unopened packaging for 18 months. Must not be exposed to temperatures below +5° C or above +30° C. After long storing, shake before use.
concrete: max. 3.5 w-% or 85 % RH
Acrylate copolymer
Remains tacky after tacky film formation.
The substrate must be dry, firm, even and free from dust and adhesion-impairing substances. Generally, levelling of concrete substrates with a suitable low-alkaline levelling compound from Kiilto is recommended.
Important! When installing on top of existing material, ensure that the material is suitable as a substrate. Installation on top of older existing plastic carpet is not recommended, high risk of plasticizers migration.
Note! For areas with castor wheel traffic, the substrate should have a surface tensile strength > 1.0 MPa. Always follow the flooring manufacturer’s recommended installation instructions for removable textile and vinyl coverings with tape effect.
Working method:
- Shake well before use.
- Apply adhesive with a short-haired roller or steel trowel. Use enough adhesive to get a good adhesion.
- Install the covering when the adhesive has reached the working time tacky gluing.
- Roll/press the material firmly.
Absorbent substrates can be primed with Kiilto Start Primer diluted 1/4 primer/water to prolong the working time.
Note! If floor covering is installed with wet bonding it becomes permanent installation.
When the textile tile backing is weak, the adhesive needs to be diluted with 5% water so the tile can be replaced without breaking.
CLEANING
Fresh adhesive is removed with water. Old adhesive can be removed by applying an alkaline cleaner PH 8-12 to the adhesive. Let the cleaner take effect for about 10-15 minutes. Remove the softened adhesive by hand or with a low speed scrubber and rinse the surface with clean water. Repeat treatment if necessary.
When cleaning an old coating, ensure that the substrate can withstand an alkaline cleaning. Finish by rinse the surface with clean water. Always follow the manufacturer's instructions and dosage.
The working times specified in this product sheet are based on laboratory tests at a temperature of +18-20°C and humidity of 50% RH. Note that drying times are affected by temperature and humidity. Variations in local working conditions and practices affect the product’s performance and results. We guarantee the high quality of our products according to our Quality Management System. We take no responsibility for incorrect use of the product or prevailing working conditions that we have no control over. We cannot be held responsible for the final result. Correct use of the product assumes that the user has read and is aware of the contents of the work instructions, if any.
We recommend using suitable protective gloves and goggles. In case of eye contact, rinse immediately with water. Avoid unnecessary skin contact with the fresh product, in case of skin contact wash with soap and water. See more information in the safety data sheet. More information on the disposal of the product and packaging can be found at www.kiilto.com.