Kiilto TopPlan DF
Smoothing compound
A floor smoothing compound with excellent self-levelling properties. Especially for floors that will be covered with a floor covering. Gives a hard and smooth surface. Also suitable for levelling floors that will be painted. Low alkali.
Special features
- dust reduced, self-levelling, fast, pumpable, paintable
- fine smoothings of floors
- coverage 1.6 kg/m²/mm
- walkable: 5 h
- coatable in 10 mm/16 h
- interior areas
Links
Materials
Suitable for levelling floor surfaces at thicknesses of 1–10 mm before laying the floor covering. In small areas (approx. 1 m²) at a thickness of up to 20 mm.
The substrate must be clean, solid and firm. Remove cement laitance, paint splashes, adhesive residue and other impurities, and brush or vacuum the floor thoroughly.
Concrete subfloors are pre-treated with 1:4 diluted Kiilto Start Primer or Primer One (20% Kiilto primer/80 % water) prior to the application of the floor screed. Surfaces under renovation as well as board surfaces must be primed with undiluted Kiilto Start Primer or Kiilto PrimerOne before levelling. Non-absorbent substrates, such as ceramic tiles or painted surfaces, can be treated also with Kiilto Fix Primer.
A low alkaline screed layer protects the adhesive and vinyl coating from the damage caused by alkaline moisture in the concrete. The studies have shown that a 5 mm thick screed layer provides the protective effect.
The concrete subfloor must comply with national standards.
| Package Size | EAN Code |
|---|---|
| 20 kg | 6411512292205 |
Optimal +18–23 °C, minimum +10 °C
> 2 MPa, EN 13813
CT-C30-F10 (EN13813), M1
10 mm / 16 h
( 23 ºC, 50 % RH )
C30 ( > 30 MPa), EN 13813
1.6 kg/m² (1 mm layer thickness)
One bag gives approx. 12 litres mass.
A2fl-s1
F10 ( > 10 MPa), EN 13813
1–10 mm
20 mm in small areas, max 1m²
0.3 mm
4,8–5,0 l water / 20 kg bag
20 kg bag
< 0,4 ‰ ( 23 ºC, 50 % RH )
Unopened package 1 year in a dry place
Concrete < 90 % RH
Resin-special cement-quartz-based powder
Flow rate 155–165 mm, EN 12706
approx. 5 hours ( 23 ºC, 50 % RH )
30–40 minutes ( 23 ºC, 50 % RH )
< 11 (low alkali)
Fill the mixing container with the required amount of clean water. Strew TopPlan DF powder slowly while stirring in cool (+10–25 °C), clean water until a smooth, flexible mass is formed. Let the mix mature for approx. 2 min. and then remix once before use.
Apply screed evenly by using a steel or notched trowel. Screed can also be applied by using an appropriate floor screed pump. The layer must be dry before a new layer is applied.
The drying of the screed must not be accelerated by heat or ventilation, since too quick a drying may cause hair cracks. If the temperature in the levelled room is higher than normal, the relative humidity very low, or if the levelled floor surface is exposed to direct sunlight, we recommend covering the floor with a tarpaulin as soon as it is dry enough to allow walking. The floor should be covered with a flooring relatively soon after it has hardened and dried. This will prevent the surface from over drying, cracking and becoming loose.
Suitable also for floors that are going to be painted in secondary rooms with light traffic, but not, for example, in garages or for bathroom floors.
In areas where waterproofing is used, e.g., bathroom floors, floor levelling should be applied under the waterproofing membrane.
Not suitable for areas permanently under water (e.g., swimming pools).
Note! Avoid excessive use of water, since it will weaken the surface strength and may cause separation or cracking.
The information given in this product data sheet is based on our tests and our practical knowledge. The technical data is defined in standard conditions. Variations in local working conditions and methods will affect the product performance and result. We guarantee the high quality of our products according to our Quality Management System. No liability can be accepted from incorrect use of the product or prevailing conditions, over which we have no control. Thus, we cannot be held responsible for the final result. The correct use of the product presupposes that the user has made him/herself aware of the contents of the working instructions and procedure guide, if provided.
Avoid unnecessary skin contact and exposure to the fresh product, use safety gloves. Refer to material safety data sheet. For information on product and package disposal, go to www.kiilto.com.