Kiilto Pro Easyrapid
Fast-setting smoothing compound

A very rapid smoothing compound for finishing levellings in indoor areas. Patching up to 10 mm. Walkable approx. 45 min. Ready to receive a floor covering as soon as 1–2 h from levelling. Concrete or levelling compound substrates do not need priming. Low alkali. Cementitious.

Special features

  • light and easy to spread, paste consistency
  • for fast finishing levellings in wet areas or dry indoor areas
  • coverage 1.1 kg/m²/mm
  • long working time, gains strength fast
  • coatable 1–2 h

Links

Materials

Application

A fast-setting pastelike smoothing compound for floors at thicknesses between 0–5 mm before laying a floor covering. For smaller areas, e.g. patching and filling, up to 10 mm. For thicker layers we recommend Maxirapid. Pro Easyrapid is not recommended for subfloor smoothing under glued down parquet flooring.

The substrate must be clean, solid and firm. Remove cement laitance, paint splashes and other impurities, and brush or vacuum the floor properly. Rough, uneven areas and high ridges in concrete must be sanded before the levelling. When patching, filling holes or levelling concrete or levelling compound substrate, no priming is needed. Renovation substrates, as well as board substrates, must be primed with undiluted Kiilto Start Primer before smoothing.

Package Size EAN Code
10 kg 6411512175102
Application temperature

optimal +18–20 °C, minimum +10 °C

Bond strength

> 1 MPa, EN 13813

Classifications and certificates

CT-C25-F6 (EN13813), M1

Coatable

1-2 h

Compression strength

C25 (> 25 MPa), EN 13813

Coverage

1 mm layer/m² solid matter weighs approx. 1.1 kg (approx. 8–9 litres of screed/bag).

Fire class

A2fl-s1

Flexural strength

F6 (> 6 MPa), EN 13813

Layer thickness

0-5 mm

Max. grain size

approx. 0.25 mm

Mixing ratio

2.6–3.0 l water / 10 kg bag

Package sizes

10 kg bag

Shrinkage

< 0.8 ‰ (23 °C, 50 % RH)

Storage

In an unopened package 9 months in dry conditions

Substrate humidity

concrete < 90 % RH

Type/binder

Polymer-special cement-sand / limestone-based powder

Walkable

approx. 45 min

Working time

Approx. 20 min

pH

< 11 (low alkali)

Instructions for use

Fill the mixing container with the required amount of clean water. Strew powder while stirring in cool (+10–20 °C), clean water until a smooth, pastelike mass is formed. Apply immediately to a clean surface using a steel trowel.

The floor should be covered with a flooring relatively soon after it has hardened and dried. This will prevent the surface from over drying, cracking and loosening.

Not recommended for smoothing of floors to be painted.

In areas where waterproofing is used, e.g. bathroom floors, floor levelling should be applied under the waterproofing membrane.

Not suitable for areas permanently under water (e.g. swimming pools).

Note! Avoid excessive use of water!

Additional information

The information given in this product data sheet is based on our tests and our practical knowledge. The technical data is defined in standard conditions. Variations in local working conditions and methods will affect the product performance and result. The result is also strongly affected by working methods. We guarantee the high quality of our products according to our Quality Management System. No liability can be accepted from incorrect use of the product or prevailing conditions, over which we have no control. Thus, we cannot be held responsible for the final result. To use the product properly, please read the product brochure, work instructions and the safety data sheet available at www.kiilto.com.

Environment and safety

Avoid unnecessary skin contact and exposure with the fresh product, use safety gloves. Please refer to the material safety data sheet. For information on product and package disposal, visit www.kiilto.com.

M1 emission classification for building material
CE marking
LEED
rapid
Key Flag
The Nordic Swan Ecolabel