Kiilto Easyrapid DF Pikatasoite 0–5 mm

Fast-setting, dust reduced smoothing compound for floors. Patching up to 10 mm. Ready to receive a floor covering as soon as 1–2 h from levelling. No priming needed. Low alkali. Cementitious.

Special features

  • very fast-setting smoothing compound for finishing floors 
  • easy to apply, paste formula
  • walkable in less than 1 h
  • coatable 1 h
  • coverage 1.1 kg/m²/mm

Materials

Application

Fast-setting smoothing compound with paste formula for the smoothing of floors at thicknesses of between 0–5 mm before laying a floor covering. For smaller areas, e.g., patching and filling, up to 10 mm. For thicker layers we recommend Maxirapid. Easyrapid DF is not recommended for subfloor smoothing under glued down parquet flooring. Thanks to new technology the product produces almost no dust during the mixing process.

The substrate must be clean, solid and firm. Remove cement laitance, paint splashes and other impurities, and brush or vacuum the floor thoroughly. Rough, uneven areas and high ridges in concrete must be sanded before carrying out the levelling. When patching, filling holes or levelling concrete, or levelling compound substrate, no priming is needed. Renovation substrates as well as board substrates must be primed with undiluted Kiilto Start Primer before smoothing.

Package Size EAN Code
10 kg 6411512083100
Application temperature

Optimal +18–20 °C, minimum +10 °C

Bond strength

> 1 MPa, EN 13813

Classifications and certificates

CT-C25-F6 (EN13813), M1

Coatable

1–2 h

Compression strength

C25 (> 25 MPa), EN 13813

Coverage

1 mm layer/m² solid matter weighs approx. 1.1 kg (approx. 8–9 litres of screed/bag).

Flexural strength

F6 (> 6 MPa), EN 13813

Layer thickness

0–5 mm

Max. grain size

Approx. 0.25 mm

Mixing ratio

2.8–3.4 l water / 10 kg bag

Package sizes

10 kg bag

Shrinkage

< 0.8 ‰ (23 °C, 50 % RH)

Storage

Unopened package in a dry place 6 months.

Substrate humidity

Concrete < 90 % RH

Type/binder

polymer-special cement-quartz sand-based powder

Walkable

Approx. 45 min

Working time

Approx. 15 min.

pH

< 11 (low alkali)

Instructions for use

Fill the mixing container with the required amount of clean water. Strew powder while stirring in cool (+10–20 °C), clean water until a smooth, paste-like mass is formed. Apply immediately to a clean surface using a steel trowel.

The floor should be covered with a flooring relatively soon after it has hardened and dried. This will prevent the surface from over drying, cracking and becoming loose.

Not recommended for the smoothing of floors that are going to be painted.

In areas where waterproofing is used, e.g., bathroom floors, floor levelling should be applied under the waterproofing membrane.

Not suitable for areas permanently under water (e.g., swimming pools).

Note! Avoid excessive use of water!

Additional information

The information given in this product data sheet is based on our tests and our practical knowledge. The technical data is defined in standard conditions. Variations in local working conditions and methods will affect the product performance and result. We guarantee the high quality of our products according to our Quality Management System. No liability can be accepted from incorrect use of the product or prevailing conditions, over which we have no control. Thus, we cannot be held responsible for the final result. The correct use of the product presupposes that the user has made him/herself aware of the contents of the working instructions and procedure guide, if provided.

Environment and safety

Avoid unnecessary skin contact and exposure with the fresh product, use safety gloves. Refer to material safety data sheet. For information on product and package disposal, go to www.kiilto.com.

M1 emission classification for building material
CE marking
LEED
The Nordic Swan Ecolabel
Key Flag